TOPIC:

Q0: I don't know how to install IM128/IV128 driver.
I had a problem during installation.
I want to update my IM128/IV128 new drivers.
Q1: How to use NDIS to connect the ISP?
Q2: How to use WINISDN to connect the ISP?
Q3: How to use VCOMM and dial-up network to connect the ISP which is PPP ?
Q4: How to use VCOMM and Chameleon 5.0 to connect the ISP?
Q5: How to use V.120 in VCOMM?
Q6: How to use V.110 in VCOMM?
Q7: When I install the NDIS, I got a endless loop of installation.
Each time power off and power on, the win95 still want me to
insert the driver, even I had truly installed them.
Q8: I can connect the ISP, but I can't browse or FTP.
Q9: How to connect the Multi-link PPP in VCOMM mode?
Q10: Now I use the VCOMM driver, I get the "device is
occupied by other device" message when I try to use
the dial-up network or other terminal program.
Q11: When running Application Program (APs) , system appears
"Open port fail "
Q12: How to use Dial-Up Networking?
Q13: How to use BOD in VCOMM mode?
Q14: How to use LZS?
Q15: When I uses dial-up network and IM128/IV128 with the NDIS driver, I get
the "The modem is being used by another Dial-Up Networking connection
or another program".
Q16: When I uses dial-up network and IM128/IV128 with the NDIS driver,
I get the "dialing", but can not get "Verifying user name and
password".
Even if switch type, SPID, DN is OK. ( in Windows 95 )
Q17: How do I make sure my installation result is OK?
Q18: How to use WINISDN to act as PPP/MP server?
Q19: How do I install IM128 CAPI driver for Windows NT 4.0?
Q20: How do I uninstall IM128 CAPI driver for Windows NT 4.0?
Q21: empty
Q22: empty
Q23: For IV128 VCOMM mode, I just have the ISDN line, but I want to
connect the remote side which is a modem. Is it possible ?
Q24: For IV128 VCOMM mode, how do I connect remote side's modem through
PSTN line?
Q25: How to make a phone call with IV128 through ISDN line?
Q26: How to make a FAX transfer with IV128 through PSTN line in VCOMM
mode ?
Q27: How to make a FAX transfer with IV128 through ISDN line in VCOMM
mode ?
Q28: How do I install IV128 CAPI driver for Windows NT 4.0?
Q29: How do I uninstall IV128 CAPI driver for Windows NT 4.0?



TROUBLE SHOOTING:

Q0: I don't know how to install IM128/IV128 driver.
I had a problem during installation.
I want to update my IM128/IV128 new drivers.
A0:
(1) Begin
If you had installed our driver before, please go to
(2) first then (3).
If you hadn't installed our driver before, please diectly
go to (3).

(2) How to Uninstall our drivers
First using the method (A) to uninstall driver, for
some reason, if it's not successful, you can use the
method (B). If still not working, try method (C).
(A) Using "Configuration Utility"
Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
Select the "Uninstall" pop-pup menu.
Before restarting Windows 95, please remove our
IM128/IV128 card and go to (3)
(B) Manually uninstall method1
For some reason, you can't uninstall the driver,
we tell you how to uninstall manually.
Insert our IM128/IV128 CARD in PCMCIA socket.
Click the "System" icon in "Control Pannel".
Select the "Device manager", click 2 times of
"Multi-function adapters", you will see
"Intelligent PCMCIA ISDN TA Multi-Function Card",
high-light it and select the "remove" command
button.
Before restarting Windows 95, please remove our
IM128/IV128 card .
If your card is IM128, delete the following files
del c:\windows\inf\compi.inf
del c:\windows\inf\mdmpi.inf
del c:\windows\inf\mfpisdn.inf
del c:\windows\inf\pisdn.inf
del c:\windows\inf\ndiswan.inf
del c:\windows\inf\netim128.inf
del c:\windows\inf\oem*.inf
If you use the OSR2/Memphis/Windows 98, please also
delete the file
del c:\windows\inf\other\ItelligentMFPISDN.inf
And if your card is IV128, delete the following files
del c:\windows\inf\com_i_m.inf
del c:\windows\inf\mdm_i_m.inf
del c:\windows\inf\mf_i_m.inf
del c:\windows\inf\p_i_m.inf
del c:\windows\inf\ndiswan.inf
del c:\windows\inf\netim128.inf
del c:\windows\inf\oem*.inf
If you use the OSR2/Memphis/Windows 98, please also
delete the file
del c:\windows\inf\other\Itelligent ISDNMF_I_M.inf
Before restarting Windows 95, please go to (3).
(C) Manually uninstall method2 ( using registry)
For some reason, you can't uninstall the driver with
the preceding 2 methods, we tell you how to uninstall
by deleting the registry.
If your card is IM128, delete the following files
del c:\windows\inf\compi.inf
del c:\windows\inf\mdmpi.inf
del c:\windows\inf\mfpisdn.inf
del c:\windows\inf\pisdn.inf
del c:\windows\inf\ndiswan.inf
del c:\windows\inf\netim128.inf
del c:\windows\inf\oem*.inf
If you use the OSR2/Memphis/Windows 98, please also
delete the file
del c:\windows\inf\other\ItelligentMFPISDN.inf
And if your card is IV128, delete the following files
del c:\windows\inf\com_i_m.inf
del c:\windows\inf\mdm_i_m.inf
del c:\windows\inf\mf_i_m.inf
del c:\windows\inf\p_i_m.inf
del c:\windows\inf\ndiswan.inf
del c:\windows\inf\netim128.inf
del c:\windows\inf\oem*.inf
If you use the OSR2/Memphis/Windows 98, please also
delete the file
del c:\windows\inf\other\Itelligent ISDNMF_I_M.inf
And execute "regedit" in windows 95, delete the
following registry:
For IM128 --
1. HKEY_LOCAL_MACHINE\Enum\mf
\CHILD0000\PCMCIA&INTELLIGENT-ISDN_IM128-A809&0
\CHILD0001\PCMCIA&INTELLIGENT-ISDN_IM128-A809&0
\CHILD0002\PCMCIA&INTELLIGENT-ISDN_IM128-A809&0
\CHILD0003\PCMCIA&INTELLIGENT-ISDN_IM128-A809&0
2. HKEY_LOCAL_MACHINE\Enum\PCMCIA
\INTELLIGENT-ISDN_IM128-A809
3. HEKY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\ISDNAdapter\****
delete the CARDTYPE is INTELLIGENT_ISDN
4 HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\Modem\****
delete the CARDTYPE is INTELLIGENT_ISDN
5.HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\MultiFunction\****
delete the CARDTYPE is INTELLIGENT_ISDN
6. HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\Net\****
delete the CARDTYPE is INTELLIGENT_ISDN
7. HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\NetTrans\****
delete the CARDTYPE is INTELLIGENT_ISDN
8. HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\Ports\****
delete the CARDTYPE is INTELLIGENT_ISDN
For IV128 --
1. HKEY_LOCAL_MACHINE\Enum\mf
\CHILD0000\PCMCIA&INTELLIGENT_ISDN_MODEM_-IV128_-3A71&0
\CHILD0001\PCMCIA&INTELLIGENT_ISDN_MODEM_-IV128_-3A71&0
\CHILD0002\PCMCIA&INTELLIGENT_ISDN_MODEM_-IV128_-3A71&0
\CHILD0003\PCMCIA&INTELLIGENT_ISDN_MODEM_-IV128_-3A71&0
2. HKEY_LOCAL_MACHINE\Enum\PCMCIA
INTELLIGENT_ISDN_MODEM_-IV128_-3A71
3. HEKY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\ISDNAdapter\****
delete the CARDTYPE is INTELLI_ISDN_MDM
4 HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\Modem\****
delete the CARDTYPE is INTELLI_ISDN_MDM
5.HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\MultiFunction\****
delete the CARDTYPE is INTELLI_ISDN_MDM
6. HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\Net\****
delete the CARDTYPE is INTELLI_ISDN_MDM
7. HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\NetTrans\****
delete the CARDTYPE is INTELLI_ISDN_MDM
8. HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class
\Ports\****
delete the CARDTYPE is INTELLI_ISDN_MDM

Before restarting Windows 95, please go to (3).

(3) How to Install our drivers
First insert the "SETUP" disk
and executes "setup".
The default directory is "c:\program files\isdn ta configuration
ultilities", surely you can change it or not. press <Enter>
After installation, you will get the "ISDN TA configuration
utility" program group in your desk top, and you will
see 3 icons, one is "Configuration", one is "Terminal" and
the other is "Status" (For the "Status", you can dynamcally
know D-CH, B1-CH, B2-CH active or not and which protocols run in
each B-CH).
Now you can select one of the following methods to install our driver:
(A) Install from disks "NDIS", then "VCOMM", then "CAPI"
1. Enter win95.
2. Please check the "Control pannel" -- "System".
The PCMCIA socket should present and work.
If not, select "Add New Hardware" in Control pannel and install
the "PCMCIA socket". At last, you should power on again.
3. IMPORTANT:Install the "ISDN acclerator PACK" or "Dial
up network 1.2" from Microsoft for Windows 95 first.
( Note: Cannot install them to Windows 98. )
4. The "Dial-Up Adapter" should present in "Network" of
Control pannel. If not, please go to "Add/Remove programs"
in Control pannel and add the "Communication" of the
"Windows Setup" tab. At last you should restart
again.
5. The TCP/IP protocol should present in "Network" of
Control pannel. If not, please add the Microsoft TCP/IP
protocol in the "Network" and restart again.
6. Plug the S/T or U dongle you purchased to the wall.
7. Insert our IM128/IV128 card in PCMCIA socket, the "New
Hardware found" will appear.
Please select the option "Manufacture driver".
Insert the disk labeled "NDIS" into floppy A and keyin A: <Enter>.
( Note: If your system is Windows 98, please copy the ndiswan.98
to ndiswan.inf first. )
It will then request the "VCOMM, "CAPI" disks.
8. Now the install process begin. When the ISDN Acclerator
PACK menu appears, select the switch type and give your
telephone number (SPID and DN).
9. Sometimes it will need your Win95 SRC. Please give the
right directory.
10.When everything done, the default mode you get will be
NDIS, if you want to change the switch
type, SPID or DN, you can use our "Configuration
Utility" to do it. Don't forget to click the "Enter"
command button in screen. But in NDIS version, you should
restart Windows 95 again.
(a)If you want to use NDIS, please see Q1&A1.
(b)If you want to change to VCOMM mode, please click
the "Configuration Utility", select the pop-pup menu
"Mode" and then the "Mode change" item.
Because you install from "NDIS" disk, you will have the
NDIS, VCOMM, WINISDN and CAPI options. Select the VCOMM
you want and restart windows 95 again.
When Windows 95 start, sometimes you will get the
network problem message in your screen, you can
ignore it, it's because the NDIS doesn't exist.
Go to the "Configuration Utility" again, select
the switch type, protocol( if you want to connect
the ISP, select the "ASYNC to SYNC ppp conversion")
SPID, DN, PPP or Multilink-PPP, 56K or 64K.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see Q3&A3
if you want to connect the ISP using dialup network.
See Q4&A4 if you want to connect the ISP using
Chameleon 5.0.
(c)If you want to change to WINISDN mode, please click
the "Configuration Utility", select the pop-pup menu
"Mode" and then the "Mode change" item.
Because you install from "NDIS" disk, you will have the
NDIS, VCOMM, WINISDN and CAPI options. Select the WINISDN
you want and restart windows 95 again.
Go to the "Configuration Utility" again, select
the switch type, SPID, DN.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see Q2&A2
if you want to connect the ISP.
(d)If you want to change to CAPI mode, please click
the "Configuration Utility", select the pop-pup menu
"Mode" and then the "mode change" item.
Because you install from "NDIS" disk, you will have the
NDIS, VCOMM, WINISDN and CAPI options. Select the CAPI
you want and restart windows 95 again.
Go to the "Configuration Utility" again.
If you select switch type to be ETSI or INS64, you don't
need to give the phone number.
If you select switch type to be NI1, AT&T5ESS, DMS100,
you should also give the correct SPID and DN.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see im_capi.q&a
if you want to make connection.


(B) Install from disks "VCOMM", then "CAPI", then "NDIS"
1. Enter win95.
2. Please check the "Control pannel" -- "System".
The PCMCIA socket should present and work.
If not, select "Add New Hardware" in Control pannel and install
the "PCMCIA socket". At last, you should power on again.
3. The "dial-up adapter" should present in "network" of
Control pannel. If not, please go to "Add/Remove programs"
in Control pannel and add the "Communication" of the
"Windows Setup" tab. At last you should restart
again.
4. The TCP/IP protocol should present in "Network" of
Control pannel. If not, please add the Microsoft TCP/IP
protocol in the "Network" and restart again.
5. Plug the S/T or U dongle you purchased to the wall.
6. Insert our IM128/IV128 card in PCMCIA socket, the "New
Hardware found" will appear.
Please select the option "Manufacture driver".
Insert the disk labeled "VCOMM" into floppy A and
keyin A: <Enter>.
It will then request the "CAPI", "NDIS" disks.
7. When everything done, the default mode you get will be
VCOMM,
(a) If you want to use VCOMM, go to the "Configuration Utility"
, select the switch type, protocol( if you want to connect
the ISP, select the "ASYNC to SYNC ppp conversion")
SPID, DN, PPP or Multilink-PPP, 56K or 64K.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see Q3&A3
if you want to connect the ISP using dial-up network.
And see Q4&A4, if you want to connect the ISP using
the Chameleon.
(b)If you want to change to WINISDN mode, please click
the "Configuration Utility", select the pop-pup menu
"Mode" and then the "mode change" item.
Because you install from "VCOMM" disk, you will have the
VCOMM, WINISDN and CAPI options. Select the WINISDN
you want and restart windows 95 again.
Go to the "Configuration Utility" again, select
the switch type, SPID, DN.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see Q2&A2
if you want to connect the ISP.
(c)If you want to change to CAPI mode, please click
the "Configuration Utility", select the pop-pup menu
"Mode" and then the "mode change" item.
Because you install from "VCOMM" disk, you will have the
VCOMM, WINISDN and CAPI options. Select the CAPI
you want and restart windows 95 again.
Go to the "Configuration Utility" again.
If you select switch type to be ETSI or INS64, you don't
need to give the phone number.
If you select switch type to be NI1, AT&T5ESS, DMS100,
you should also give the correct SPID and DN.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see im_capi.q&a
if you want to make connection.
8. If you can't connect, check your switch type, SPID, DN
TCP/IP settings are correct or not.
Maybe you can restart Windows 95 and try again.

(C) Install from disks "CAPI", then "VCOMM", then "NDIS"
1. Enter win95.
2. Please check the "Control pannel" -- "System".
The PCMCIA socket should present and work.
If not, select "Add New Hardware" in Control pannel and install
the "PCMCIA socket". At last, you should power on again.
3. The "dial-up adapter" should present in "network" of
Control pannel. If not, please go to "Add/Remove programs"
in Control pannel and add the "Communication" of the
"Windows Setup" menu. At last you should restart
again.
4. The TCP/IP protocol should present in "Network" of
Control pannel. If not, please add the Microsoft TCP/IP
protocol in the "Network" and restart again.
5. Plug the S/T or U dongle you purchased to the wall.
6. Insert our IM128/IV128 card in PCMCIA socket, the "New
Hardware found" will appear.
Please select the option "Manufacture driver".
Insert the disk labeled "CAPI" into floppy A and
keyin A: <Enter>.
It will then request the "VCOMM", "NDIS" disks.
7. When everything done, the default mode you get will be
CAPI,
(a)If you want to use CAPI mode,
Go to the "Configuration Utility" again.
If you select switch type to be ETSI or INS64, you don't
need to give the phone number.
If you select switch type to be NI1, AT&T5ESS, DMS100,
you should also give the correct SPID and DN.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see im_capi.q&a
if you want to make connection.
(b)If you want to change to VCOMM mode, please click
the "Configuration Utility", select the pop-pup menu
"Mode" and then the "mode change" item.
Because you install from "CAPI" disk, you will have the
CAPI, VCOMM, WINISDN options. Select the VCOMM
you want and restart windows 95 again.
Go to the "Configuration Utility" again, select
the switch type, protocol( if you want to connect
the ISP, select the "ASYNC to SYNC ppp conversion")
SPID, DN, PPP or Multilink-PPP, 56K or 64K.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see Q3&A3
if you want to connect the ISP using dialup network.
See Q4&A4 if you want to connect the ISP using
Chameleon 5.0.
(c)If you want to change to WINISDN mode, please click
the "Configuration Utility", select the pop-pup menu
"Mode" and then the "mode change" item.
Because you install from "CAPI" disk, you will have the
CAPI, VCOMM, WINISDN options. Select the WINISDN
you want and restart windows 95 again.
Go to the "Configuration Utility" again, select
the switch type, SPID, DN.
At last, don't forget to click the "Enter" command
button in screen. Leave the Utility and see Q2&A2
if you want to connect the ISP.
8. If you can't connect, check your switch type, SPID, DN
TCP/IP settings are correct or not.
Maybe you can restart Windows 95 and try again.

TOP
Q1: How to use NDIS to connect the ISP?
A1:
1.Install IM128/IV128, see Q0&A0.
(You can use our Configuration Ultility to change the switch
type and phone number if you want, but remember to restart
Windows 95 again.)
2.Go to the Dial-up Networking.
Click "Make new Connection", give the connection name
,for example, NDIS_2, and slect one of two Lines( for
example ,ISDN-lineX, X maybe 1,2,3,4.....).
Now we assume that you have 2 lines, ISDN-line0 and
ISDN-line1.
3.Click (uses the right button of mouse) the icon named
NDIS_2 ( you just gave it). Click "Propertities" menu.
In "General" menu, please gives the phone number you
want to dial, and select the ISDN-Line0 in "using"
command dialog.
If you want to change between 64K and 56K, please click
the "Configure" command button.
If you want to dial with the Multi-Link PPP, please click
the "Settings" command button. And add the additional
devices using the ISDN-line1.
In the "Type of Dial-Up Server" menu, please select the
PPP: Win95, Windows NT 3.5, Internet
The "Advance options", you can unselect the following 3
items:
Log on to network
Enable software compression
Require encrypted password
The "Allowed network protocols", please
unselect the
NETBEUI
IPX/SPX compatible
select the
TCP/IP
Click the "TCP/IP Settings", you can specify an IP address
if you need, and specify name server address if you
need.
4.Finally, you can use our card to connect to Internet

TOP
Q2: How to use WINISDN to connect the ISP?
A2:
1.Install IM128/IV128, see Q0&A0.
(You can use our Configuration Ultility to change the switch
type and phone number if you want)
2. We assumed that you want to use Chameleon NetManage 5.0
for WINISDN.
IMPORTANT: Please backup the file
c:\windows\system\wsock32.dll
and copy it to another file (ex. wsock32.ms).
This is because the Chameleon 5.0 will replace this file.
Install the Chameleon 5.0 AP.
At the end of installation, it will request you to install
the NetManage TCP/IP protocol, please add the "NetManage
TCP/IP v5.0 Dialup only" protocol in "Network" of "Control
pannel". If it wants the Windows 95 SRC, please give the
right path. If it wants the Chameleon path, you can give
"c:\netmanag.95".
After that, it will request you to restart Windows 95,
before restart, please make sure the path in c:\autoexec.bat
is "c:\netmanag.95;", not "c:\netmanag.95;=", sometimes it
causes error.
Restart windows, go to DOS SHELL, check the c:\windows\
system\wsock32.dll, the size should be different from
wsock32.ms (you just copy it), please copy the new
wsock32.dll to wsock32.che.
From now, if you want to run dial-up network in the future,
executes
copy wsock32.ms wsock32.dll
if you want to run Chameleon 5.0, executes
copy wsock32.che wsock32.dll
3. Now you can click the icon "Internet Chameleon 5.0" in
desk top. Slect the "Custom Configuration" icon in
"Internet Chameleon 5.0" program group.
In the pop-pup menu "Interface", select the "Add" item,
give a name (ex. IM128WINISDN).
In the combo-box "Type", give the "ISDN", this means
we want to use WINISDN.
The device you keyin will appears in the list box of
main window. Click 2 times in the "IM128WINISDN", you can
now configure it.
In the "IP Configuration" tab, you can give the IP address
if you want.
In the "Name Resolution" tab, you can give the Domain Servers
if you want.
In the "dial" tab, you can add all the telephone numbers
you belonged to the list box.
In the "Call Type" tab, you can give the Speed (56K/64K
for 1 B channel, 112K/128K for 2 B channels), if you select
112K/128K, please also give the Primary and Secondary number.
In the "Login" tab, please give the UserName and User Password.
Click the "OK" command button if you finish.
At last, Click the "Connect" button if can access the Internet.
4. Finally, you can use our card to connect to Internet

TOP
Q3: How to use VCOMM and dial-up network to connect the ISP which is PPP ?
A3:
1. Install IM128/IV128, see Q0&A0.
Go to our "Configuration Ultility".
From the tab "Switch Type" and "Call", you need to give the
correct switch type and phone number.
From the tab "Protocol", please select the "ASYNC to SYNC ppp
conversion".
From the "Other" tab, don't select the "MP Enabled" and
"BOD Enabled", and it will be single PPP.

2. Go to the Dial-up networking.
Click "Make new Connection", give the connection name
,for example, COMPORT, and slect the "Intelligent
PCMCIA ISDN TA (modem)".
3. Click (uses the right button of mouse) the
icon named COMMPORT ( you just gave it). Click the "Propertities" tab.
In "General" menu, please gives the phone number you
want to dial, and select the "Intelligent PCMCIA ISDN
TA (modem)" in "Using" command dialog.
In the "Type of Dial-Up Server" menu, please select the
"PPP: Win95, Windows NT 3.5, Internet".
The "Advance option", you can unselect the following 3
items:
Log on to network
Enable software compression
Require encrypted password
The "Allowed network protocols", please
unselect the
NETBEUI
IPX/SPX compatible
select the
TCP/IP
Click the "TCP/IP Settings", you can specify a IP address
if you need, and specify name server address if you
need.
4.Finally, you can use our card to connect to Internet

TOP
Q4: How to use VCOMM and Chameleon 5.0 to connect the ISP?
A4:
1. Install IM128/IV128, see Q0&A0.
Go to our "Configuration Ultility".
From the tab "Switch Type" and "Call", you need to give the
correct switch type and phone number.
From the tab "Protocol", please select the "ASYNC to SYNC ppp
conversion".
From the "Other" tab, don't select the "MP Enabled" and
"BOD Enabled", and it will be single PPP.
2. We assumed that you want to use Chameleon Net Manager 5.0
for VCOMM.
IMPORTANT: Please backup the file
c:\windows\system\wsock32.dll
and copy it to another file (ex. wsock32.ms).
This is because the Chameleon 5.0 will replace this file.
Install the Chameleon 5.0 AP.
At the end of installation, it will request you to install
the NetManage TCP/IP protocol, please add the "NetManage
TCP/IP v5.0 Dialup only" protocol in "Network" of "Control
pannel". If it wants the Windows 95 SRC, please give the
right path. If it wants the Chameleon path, you can give
"c:\netmanag.95".
After that, it will request you to restart Windows 95,
before restart, please make sure the path in c:\autoexec.bat
is "c:\netmanag.95;", not "c:\netmanag.95;=", sometimes it
causes error.
Restart windows, go to DOS SHELL, check the c:\windows\
system\wsock32.dll, the size should be different from
wsock32.ms (you just copy it), please copy the new
wsock32.dll to wsock32.che.
From now, if you want to run dial-up network, executes
copy wsock32.ms wsock32.dll
if you want to run Chameleon 5.0, executes
copy wsock32.che wsock32.dll
Note that the Microsoft TCP/IP should be installed befor
Chamleon 5.0 TCP/IP.
3. Now you can click the icon "Internet Chameleon 5.0" in
desk top. Select the "Custom Configuration" icon in
"Internet Chameleon 5.0" program group.
In the pop-pup menu "Interface", select the "Add" item,
give a name (ex. IM128VCOMM).
In the combo-box "Type", give the "PPP", this means
we want to use Async to Sync Conversion.
The device you keyin will appears in the list box of
main window. Click 2 times in the "IM128VCOM", you can
now configure it.
In the "IP Configuration" tab, you can give the IP address
if you want.
In the "Name Resolution" tab, you can give the Domain Servers
if you want.
In the "Port" tab, you should give the "Port" (our default is
COM5, you can change it with the Configuration Utility), and
other settings.
In the "dial" tab, you can add all the telephone numbers
you belonged to the list box.
In the "Modem" tab, you can select a "Model" to be
"Motorola BitSUFUR PRO" or just select one of the list but
let the "Modem Init" empty.
In the "Login" tab, please give the UserName and User Password.
Click the "OK" command button if you finish.
At last, Click the "Connect" button if you want to access the
Internet. After "CONNECT" message echo on the screen, press
the "DONE" button and you will enter the Internet.
4.Finally, you can use our card to connect to Internet

TOP

Q5: How to use V.120 in VCOMM?
A5:
1. Install IM128/IV128, see Q0&A0.
2. Insert our IM128/IV128 CARD in PCMCIA socket.
Plug the S/T or U dongle you purchased to the wall.
3. Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
In the "SWITCH TYPE" tab, select the switch type you want.
In the "PTOTOCOL" tab, select the V.120.
In the "CALL" tab, give the SPID and DN.
In the "OTHER" tab, you can change 64K or 56K.
At last, don't forget to click the "Enter" command
button.
4. In the "Mode" pop-pup menu, there is "port change"
item, you can change the COM port if you want.
The default COM port is COM5.
5. Install the AP you want, for example, Hyperterminal, Procomm Plus,
BitCOMM and so on.
6. If you want to use the Hyperterminal.
And your desk top doesn't have Hyperterminal yet.
Please go to "Add/Remove program" in Control pannel
and add the "Communication" of the "Windows Setup"
tab. Note that you should restart again.
7. We now assume that you use the Hyperterminal.
8. Click the "Hypertrm.exe" icon, give a name (ex, IM128COM)
, give the telephone number you want to dial and
select the "Intelligent PCMCIA ISDN TA (modem)".
If the "dial" window appear, you can select "Cancel"
first and go to the Terminal Screen.
Now you can use AT comannd sets to dial and connect the
other side with V.120.

TOP

Q6: How to use V.110 in VCOMM?
A6:
1. Install IM128/IV128, see Q0&A0.
2. Insert our IM128/IV128 CARD in PCMCIA socket.
Plug the S/T or U dongle you purchased to the wall.
3. Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
In the "SWITCH TYPE" tab, select the switch type you want.
In the "PTOTOCOL" tab, select the SVC_CSW_V110 and select
one speed.
In the "CALL" tab, give the SPID and DN.
In the "OTHER" tab, you can change 64K or 56K.
At last, don't forget to click the "Enter" command
button.
4. In the "Mode" pop-pup menu, there is "port change"
item, you can change the COM port if you want.
The default COM port is COM5.
5. Install the AP you want, for example, Hyperterminal, Procomm Plus,
BitCOMM and so on.
6. If you want to use the Hyperterminal.
And your desk top doesn't have Hyperterminal yet.
Please go to "Add/Remove program" in Control pannel
and add the "Communication" of the "Windows Setup"
tab. Note that you should restart again.
7. We now assume that you use the Hyperterminal.
8. Click the "Hypertrm.exe" icon, give a name (ex, IM128COM)
, give the telephone number you want to dial and
select the "Intelligent PCMCIA ISDN TA (modem)".
If the "dial" window appear, you can select "Cancel"
first and go to the Terminal Screen.
Now you can use AT comannd sets to dial and connect the
other side with V.110.
9. For outgoing call, you must set the V.110 DTE speed before beginning to
connect with remote side.
For incoming call, the isdn TA will auto detect the remote DTE speed
and connect it.
10.You can also use the the following AT command to configue the V.110 setting :
(1) at!z=6 : select V.110 protocol mode.
(2) atb? : display the current DTE speed (bps) of V.110 for outgoing call.
(3) atb0 : set DTE speed = 600 bps.
(4) atb1 : set DTE speed = 1200 bps.
(5) atb2 : set DTE speed = 2400 bps.
(6) atb3 : set DTE speed = 4800 bps.
(7) atb4 : set DTE speed = 9600 bps.
(8) atb5 : set DTE speed = 9600 bps.
(9) atb6 : set DTE speed = 19200 bps.
(10) atb7 : set DTE speed = 38400 bps.
(11) atb8 : set DTE speed = 57600 bps.
(12) ath : disconnect the active data call.
(13) at&w9: save the V.110 setting.


TOP


Q7: When I install the NDIS, I got a endless loop of installation.
Each time power off and power on, the win95 still want me to
insert the driver, even I had truly installed them.
A7: It is very important that our driver sould be installed after
the installation of "ISDN ACCLERATOR PACK 1.1" or "Dial up
Network 1.2" when you want to use the NDIS function in Windows 95
(Note that Windows 98 is already built in so you cannot install
the "ISDN ACCELERATOR PACK 1.1" and "Dial Up Network 1.2 again.).
If you didn't do that, you will get the endless loop during
installation.
In this situlation, please remove the card , resatrt windows
95 and reference the uninstall method in Q0&A0.
After installation, please install the MicroSoft ISDN Acclerator
Pack 1.1 or Dial-up Network 1.2 (you can download from
www.microsoft.com for Win95, but it's already in Window 98) and
then install our driver.

TOP
Q8: I can connect the ISP, but I can't browse or FTP.
A8: Maybe due to the following resons:
1. Make sure that TCP/IP protocol exists in the
"network" of the "Control Pannel".
2. Your IP address is not correct.
3. You Domain Name address is not correct.
4. Wsock32.dll is something wrong.
For example, you had installed the Chameleon 5.0, this
AP will change c:\windows\system\wsock32.dll for
Chameleon use. Next time you use the Microsoft
dial-up network, you need to restore the Microsoft
wsock32.dll, or it can't browse.

TOP
Q9: How to connect the Multi-link PPP in VCOMM mode?
A9:
1. Install IM128/IV128, see Q0&A0.
Go to our "Configuration Ultility".
From the tab "Switch Type" and "Call", you need to give the
correct switch type and phone number.
From the tab "Protocol", please select the "ASYNC to SYNC ppp
conversion".
2. Now you can have the several methods:
(1) Go to our "Configuration Ultility", click the "Other" tab,
select the "MP Enabled" and "BOD Enabled" and give the 2nd phone
number in the "MP Sec Phone Num".
If you just select the "MP Enabled" but not "BOD Enabled", you will
make 2-BCH always bundling together. When the "MP Sec Phone Num"
is empty, we will dial the same number. When not empty, it's the
2nd phone number.
If select none, you are single PPP.
If select both, first we will dial two calls and then begin the
"Bandwith On Demand" function, we will automatically drop or
add the 2nd B-CH depends on the throughput. When the "MP Sec Phone Num"
is empty, we will dial the same number. When not empty, it's the
2nd phone number.

(2) If you don't want to use our Configuration Utility,
you can directly keyin AT command sets in terminal
application program to configure it.
AT&J1 means you want to use same number to dial 2 times
and bunding together.
In the dial-up AP (for example, dial-up network),
you just need to give one number (dial-up network
will set the "ATDxxxxxxx" which xxxxxxx is the number)
and IM128/IV128 will dial the 2nd number automatically.
AT&J0 means just PPP (dial only one number) or Multi-link
PPP (dial 2 different numbers).
When AT&NM=0 , this is just PPP, dial-up AP will
set "ATDxxxxxxx" which xxxxxxx is the telephone
number.
When AT&NM=1 , AT&Z0=yyyyyyy which yyyyyyy is the
second number. You just need to set the first
number in dial-up AP, AP will give the command
"ATDxxxxxxx" which xxxxxxx is the first number
and our driver will dial the second number
"yyyyyyy".
When AT&NM=1 , but AT&Z0 is empty, this is still
just PPP, AP will dial only "ATDxxxxxxx" which
xxxxxxx is the first number.
ATDxxxxxxx&yyyyyyy
No matter AT&J, AT&NM setting, this is always
Multi-Link PPP, when you set the telephone
number to be "xxxxxxx&yyyyyyy", we will dial
the first number xxxxxxx then second number
yyyyyyy.
Except the &, you can also use the + or !
instead.

3. Go to the Dial-up networking.
Click "Make new Connection", give the connection name
,for example, COMPORT, and slect the "Intelligent
PCMCIA ISDN TA (modem)".
4. Click (uses the right button of mouse) the
icon named COMPORT ( you just gave it). Click the "Propertities" tab.
In "General" menu, please gives the phone number you
want to dial, and select the "Intelligent PCMCIA ISDN
TA (modem)" in "Using" command dialog.
In the "Type of Dial-Up Server" menu, please select the
"PPP: Win95, Windows NT 3.5, Internet".
The "Advance option", you can unselect the following 3
items:
Log on to network
Enable software compression
Require encrypted password
The "Allowed network protocols", please
unselect the
NETBEUI
IPX/SPX compatible
select the
TCP/IP
Click the "TCP/IP Settings", you can specify a IP address
if you need, and specify name server address if you
need.
5.Finally, you can use our card to connect to Internet

Note: AT&NB=1 means BOD enabled
AT&NM=1 means MP enabled
AT&Z0 is the 2nd phone number

TOP

Q10: Now I use the VCOMM driver, I get the "device is
occupied by other device" message when I try to use
the dial-up network or other terminal program.
A10:
1. Maybe your COM port is conflict with another program,
go to the "Configuration Ultility" and select "Port
change", then change the COM port. Our factory COM port
is COM5.
2. In some special case , the other device in COM port will
effect the ISDN COM port function . Please remove all the
other devices in "Modem" of "System".

TOP

Q11: When running Application Program (APs) , system appears
"Open port fail "
A11:
1. Please check the ISDN card have been Plug In .
2. If you ever run the AP successfully, and Windows 95 suddently
shows "Open port fail",it is probably the ISDN TA PC card
is use by the other APs. Terminate the other APs and try again.
3. Enter Our ISDN configuration utility, check the current active
API shown at the bottom of the Utility Manager's main screen,
and make sure the AP uses the consistent API with the current
active mode. If not , select the approprite API for the AP.
4: In some special case , the other device in COM port will effect
the ISDN COM port function . Please remove all the other device
in "Modem" of "System".
5. If all the above solution do not work , uninstall the ISDN TA
PC Card and install it once again .

TOP
Q12: How to use Dial-Up Networking?
A12:
1. Open <Dial-Up Networking>.
2. Open <Make New Connection>.
3. Type a name for the computer you are dialing: <My Connection>.
4. Select a modem: <Intelligent PCMCIA ISDN TA (modem)>.
5. Select <Configure>.
6. Select <Options>.
7. Set <Bring up terminal window before dialing>.
8. Select <OK>.
9. Select <Next>.
10. Type the phone number for the computer you want to call.
11. Select <Next>.
12. Select <Finish>.
13. Click right mouse button on <My Connection>.
14. Select <Properties>.
15. Select <Server Types>.
16. Clear <Enable software compression>.
17. Select <OK>.
18. Open <My Connection>.
19. Select <Connect>.
20. Enter any AT commands if necessary.

TOP
Q13: How to use BOD in VCOMM mode?
A13: See Q9&A9

TOP

Q14: How to use LZS?
A14:
1. Please refer to <How to use Dial-Up Networking>.
2. AT&NCM=3 Set LZS own check mode to Sequence Number.
3. AT&NCP=1 Enable LZS.
4. AT&NHC=1 Set LZS own history count to 1.
5. Select <Continue (F7)>.


Summary of AT commands for LZS

AT&NCM=0 Set LZS own check mode to None
AT&NCM=1 Set LZS own check mode to LCB
AT&NCM=2 Set LZS own check mode to CRC
AT&NCM=3 Set LZS own check mode to Sequence Number
AT&NCM? Query LZS own check mode
AT&NCP=0 Disable LZS
AT&NCP=1 Enable LZS
AT&NCP?
AT&NHC=0 Set LZS own history count to 0
AT&NHC=1 Set LZS own history count to 1
AT&NHC? Query LZS own history count

TOP
Q15: When I uses dial-up network and IM128/IV128 with the NDIS driver, I get
the "The modem is being used by another Dial-Up Networking connection
or another program".
A15:
1. Check to see if you select "ISDN-linex" ( which x is 0,1,2,..)
as the modem device in the dial up network.
2. Be sure "ISDN-linex" is not occupied by another program.
3. Go to the Configuration Utility and make sure the Switch Type,
SPID, DN are all correct, and then restart windows 95 again.

TOP
Q16: When I uses dial-up network and IM128/IV128 with the NDIS driver,
I get the "dialing", but can not get "Verifying user name and
password".
Even if switch type, SPID, DN is OK. ( in Windows 95 )
A16:
1. Uninstall our driver
2. Reinstall ISDN Acclerator Pack again
3. Reinstall our driver again
4. Go to the Configuration Utility and make sure the Switch Type,
SPID, DN are all correct, and then restart windows 95 again.

TOP
Q17: How do I make sure my installation result is OK?
A17:
1. Click the "System" icon in "Control Pannel".
Select the "Device manager", make sure there is not
"!" or "?" mark in:
(For IM128)
"ISDN Adapter" --
"Intelligent PCMCIA ISDN TA (ISDN)"
"Multi-function adapters" --
"Intelligent PCMCIA ISDN TA Multi-Function Card",
"COM & LPT" --
"Intelligent PCMCIA ISDN TA (COM port) (COM5)"
"Network Adapters" --
"Intelligent PCMCIA ISDN TA (Net)"
"Modems" --
"Intelligent PCMCIA ISDN TA (modem)"
(For IV128)
"ISDN Adapter" --
"Intelligent ISDN MODEM (ISDN)"
"Multi-function adapters" --
"Intelligent PCMCIA ISDN TA Multi-Function Card",
"COM & LPT" --
"Intelligent PCMCIA ISDN TA (COM port) (COM5)"
"Network Adapters" --
"Intelligent PCMCIA ISDN TA (Net)"
"Modems" --
"Intelligent ISDN MODEM (modem)"
2. If there is "!" mark in "Intelligent PCMCIA ISDN TA
Multi-Function Card", maybe the I/O, IRQ assignment
from Windows 95 are fail. Double click the "Intelligent
PCMCIA ISDN TA Multi-Function Card", select the tab
"Resource", you will see the 2 I/O (for IM128, one is 16 bytes
and the other is 1 byte, for IV128, both are 8 bytes) and 1 IRQ.
I/O cannot be zero and IRQ cannot conflict with other devices.
Sometimes if you change the setting of IRQ and give
free I/Os (16 bytes, 1 byte for IM128 and 8 bytes, 8 bytes for
IV128) it will solve the problem although they doesn't conflict.
For the IRQ problem, see the 2 examples:
(1) If there isn't any IRQ free, try to disable one device
(for example, COM2 or sound card), uninstall our driver
and reinstall again.
(2) If there is one IRQ free but windows 95 cannot assign to
us. For example, IRQ9 is free and sound card is at IRQ5.
You can change sound card to IRQ9, then uninstall and
reininstall our driver again.
3. If there is "!" mark in "Intelligent PCMCIA ISDN TA
(COM port) (COM5)" for IM128 or "Intelligent ISDN MODEM
(COM port) (COM5)" for IV128 , maybe the COM5 is occpied by other
device.
Go to our "Configuartion Ultility", click the "port
change" and select another port, then resatrt windows 95
again.
4. If there is "!" mark in "Intelligent PCMCIA ISDN TA (Net)",
check:
(1) ISDN acclerator Pack or Dial-up network is damaged
or not exist, try to install it and our driver again.
(2) Check the files NDISWAN.VXD and ISDNUI.DLL. They should
exist in c:\windows\system.
(3) Check "Control Pannel" -- "Network", you should have:
Dial-Up Adapter
TCP/IP
Note: If your installation method is from "NDIS", "VCOMM"
to "CAPI", your interfaces are NDIS, VCOMM, WINISDN and
CAPI. If the current mode you selected is not NDIS mode,
you will get the "!" mark, this is correct, should be
ignored.
5. If there are not any "!" or "?" mark, you can use VCOMM
mode to check the PCMCIA card.
Select the VCOMM mode, try to give the "AT&K<Enter>" command
in the HyperTerminal, you should get the response like:
A55A00FF85 5AA5
ISDN Hardware is OK!
If you get "ISDN Hardwre is bad", may be your card is bad
or PCMCIA socket bad or Windows 95 I/O conflict.

6. If there isn't any proceding problems and you uses the U-dongle
to plug into the wall. You can see the "LINK" LED to identify:
(1) LED OFF:
It means Windows 95 doesn't know you inserted the card,
and there isn't power in the socket.
(2) LED is 8 Hz Flashing:
Power exists, and begin activation.
(3) LED is 1 Hz Flashing:
U active but S/T not.
(4) LED ON and solid:
U and S/T activate

7. Select the VCOMM mode, try to give the "ATH5<Enter>" command
in the HyperTerminal, you should get the response like:
ISDN Layer 1 is link success!

8. If everything is OK, but you can not connect, check the
switch type, SPID and DN is correct or not in our
Configuration Ultility.

9. No matter which interface mode you select, run our "Status"
in "Configuration Ultility" and try to connect you will know the
D-CH, B1-CH and B2-CH active or not and which protocol
currently run.

TOP

Q18: How to use WINISDN to act as PPP/MP server?
A18:
1.Install IM128/IV128, see Q0&A0.
2. We assumed that you want to use Chameleon NetManage 5.0
for WINISDN.
IMPORTANT: Please backup the file
c:\windows\system\wsock32.dll
and copy it to another file (ex. wsock32.ms).
This is because the Chameleon 5.0 will replace this file.
Install the Chameleon 5.0 AP.
At the end of installation, it will request you to install
the NetManage TCP/IP protocol, please add the "NetManage
TCP/IP v5.0 Dialup only" protocol in "Network" of "Control
pannel". If it wants the Windows 95 SRC, please give the
right path. If it wants the Chameleon path, you can give
"c:\netmanag.95".
After that, it will request you to restart Windows 95,
before restart, please make sure the path in c:\autoexec.bat
is "c:\netmanag.95;", not "c:\netmanag.95;=", sometimes it
causes error.
Restart windows, go to DOS SHELL, check the c:\windows\
system\wsock32.dll, the size should be different from
wsock32.ms (you just copy it), please copy the new
wsock32.dll to wsock32.che.
From now, if you want to run dial-up network in the future,
executes
copy wsock32.ms wsock32.dll
if you want to run Chameleon 5.0, executes
copy wsock32.che wsock32.dll
3. Now you can click the icon "Internet Chameleon 5.0" in
desk top. Select the "Custom Configuration" icon in
"Internet Chameleon 5.0" program group.
In the pop-pup menu "Interface", select the "Add" item,
give a name (ex. SERVER).
In the combo-box "Type", give the "ISDN", this means
we want to use WINISDN.
The device you keyin will appears in the list box of
main window. Click 2 times in the "SERVER", you can
now configure it.
In the "IP Configuration" tab, you can give the IP address
if you want. ( for example, you give the 140.1.1.1 and
mask bits is 255.255.0.0 then client user can use 140.1.1.4
to log in)
In the "Call Type" tab, you can give the Speed (56K/64K
for 1 B channel, 112K/128K for 2 B channels).
Click the "OK" command button if you finish.
Now you should see the "Interface" is "SERVER" and "Dial"
is "/" on the screen.
4. At last, Click the "Connect" button and wait for the incoming
call.

TOP
Q19: How do I install IM128 CAPI driver for Windows NT 4.0?
A19:
1. Enter Windows NT 4.0
2. Insert our card in the PCMICIA socket.
3. Click "Network" of the "Control Pannel". ( You have at least
already installed one kind of network card driver.)
4. Insert our "Windows NT driver disk (CAPI)" in A:
5. From the Network window, select the "Adapter" tab, click "Add".
6. Click "Have disks", give the path "A:\CAPI", click "OK".
7 Now you will get the "IM128 ISDN Adapter for CAPI" item in the
list box. Click "OK".
8. Now you get the "IM128 System IM128 Setup" window.
Please make sure that the following settings are all correct:
(A) "I/O base" can not occupied by other device.
(B) "IRQ" is not confict.
(C) "Mem" setting is for PCMICA attritube memory use, you can
select one of the settings.
(D) For the "Pcmcia" setting, if you select the "CARDBUS", you can
work with the chip like "TI 113X" and "Cirrus Logic 6832" and
"O2 MICRO OZ6833T".
If you select the "365 COMP", you can work with Intel 82365
compatible chip.
(E) Last make sure "Line settings" are all correct.
After that, click "Continue".
9. At last, click "close".
10.Restart Windows NT again.
11.Now you can check our card is installed correctly or not.
Click the Program - Administrative Tools (Common) - Windows NT
Diagnostics. Click "Service" tab and "Device" command button and
check the "isdnta" status. If the status is running, it meas
good. If it's stop, try to change the value of I/O, IRQ, Mem and
Pcmcia setting.
Make sure the I/O, IRQ, Mem setting are not conflict with other
devices. You can click "Start" -- "Program" - "Administrative Tools
(Common)" - "Windows NT Diagnostics". Click "Resource" tab, now you
can check the "IRQ" and "I/O port".
Note: If you click "Start" -- "Programs" -- "Administrative Tools"
-- " Event Viewer", you will get the message "The IM128 System
IM128 Driver Service failed to start due to the following error:
The system can not find the file specified.". This should be
ignored. It is not an error.
12.Now you can install RVS-COM for Windows NT and run the CAPI
applications.
Run "c:\windows\system\status.exe" and try to connect you will
know the D-CH, B1-CH and B2-CH active or not and which protocol
currently run.
13.If you want to change the I/O, IRQ, Mem, Pcmcia, Switch Type,
PHONE0, PHONE1, SPID0 and SPID1, click "My Computer" -- "Control
Pannel" -- "Network" and then select the "Adapter", highlight
"IM128 System IM128 Adapter", click the "Propertities" command
button. Now you can change the parameters you want.
Note: After changing some settings, you had better "power off"
and "power on". Do not let Windows NT do the "restart" for you.
It sometimes has no effect.

TOP
Q20: How do I uninstall IM128 CAPI driver for Windows NT 4.0?
A20: Click "Network" in "Control Pannel", select the "Adapter" tab,
highlight the "IM128 System IM128 Adapter". Then click "remove".

Q21: Empty
A21: Empty

Q22: Empty
A22: Empty

TOP

Q23: For IV128 VCOMM mode, I just have the ISDN line, but I want to
connect the remote side which is a modem. Is it possible ?
A23: Yes! You can select our "Modem over B channel function".
1. Install IV128, see Q0&A0.
2. Insert our IV128 CARD in PCMCIA socket.
Plug the S/T or U dongle you purchased to the wall.
3. Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
In the "SWITCH TYPE" tab, select the switch type you want.
In the "PTOTOCOL" tab, you can ignore it.
In the "CALL" tab, give the SPID and DN.
In the "OTHER" tab, you can jgnore it.
In the "MODEM" tab, select the "Modem over ISDN B-Channel".
In the "Voice Config" tab, select the "A-law for European countries"
or "U-law for North American Countries", depends on your country.
And select "Answer by Modem" if you act as the answer side.
At last, don't forget to click the "Enter" command
button.
4. In the "Mode" pop-pup menu, there is "port change"
item, you can change the COM port if you want.
The default COM port is COM5.
5. Install the AP you want, for example, Hyperterminal, Procomm Plus,
BitCOMM and so on.
6. If you want to use the Hyperterminal.
And your desk top doesn't have Hyperterminal yet.
Please go to "Add/Remove program" in Control pannel
and add the "Communication" of the "Windows Setup"
tab. Note that you should restart again.
7. We now assume that you use the Hyperterminal.
8. Click the "Hypertrm.exe" icon, give a name (ex, IV128COM)
, give the telephone number you want to dial and
select the "Intelligent ISDN MODEM (modem)".
If the "dial" window appear, select "Cancel" first and
go to the Terminal Screen.
You can enter AT!V? to check your settings is correct or not.
9. If you are in the original side, enter ATDMxxxxxxx which xxxxxxx
is your telephone number.
If you are in the answer side, just enter ATS0=1 and wait for call.

TOP
Q24: For IV128 VCOMM mode, how do I connect remote side's modem through
PSTN line?
A24:
1. Install IV128, see Q0&A0.
2. Insert our IV128 CARD in PCMCIA socket.
Plug the DAA dongle you purchased to the wall (RJ-11).
3. Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
In the "SWITCH TYPE" tab, you can ignore it.
In the "PTOTOCOL" tab, you can ignore it.
In the "CALL" tab, you can jgnore it.
In the "OTHER" tab, you can jgnore it.
In the "MODEM" tab, select the "Modem over Analog Telephone Line
(PSTN)".
In the "Voice Config" tab, you can ignore it.
At last, don't forget to click the "Enter" command
button.
4. In the "Mode" pop-pup menu, there is "port change"
item, you can change the COM port if you want.
The default COM port is COM5.
5. Install the AP you want, for example, Hyperterminal, Procomm Plus,
BitCOMM and so on.
6. If you want to use the Hyperterminal.
And your desk top doesn't have Hyperterminal yet.
Please go to "Add/Remove program" in Control pannel
and add the "Communication" of the "Windows Setup"
tab. Note that you should restart again.
7. We now assume that you use the Hyperterminal.
8. Click the "Hypertrm.exe" icon, give a name (ex, IV128COM)
, give the telephone number you want to dial and
select the "Intelligent ISDN MODEM (modem)".
If the "dial" window appear, select "Cancel" first and
go to the Terminal Screen.
You can enter AT!V? to check your settings is correct or not.
9. If you are in the original side, enter ATDTxxxxxxx which xxxxxxx
is your telephone number.
If you are in the answer side, just enter ATS0=1 and wait for call.

TOP
Q25: How to make a phone call with IV128 through ISDN line?
A25:
1. Install IV128, see Q0&A0.
2. Insert our IV128 CARD in PCMCIA socket.
Plug the S/T or U dongle you purchased to the wall.
Plug the microphone and earphone in the S/T or U dongle.
3. Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
In the "SWITCH TYPE" tab, select the switch type you want.
In the "PTOTOCOL" tab, you can ignore it.
In the "CALL" tab, give the SPID and DN.
In the "OTHER" tab, you can jgnore it.
In the "MODEM" tab, select the "Modem over ISDN B-Channel".
In the "Voice Config" tab, select the "A-law for European countries"
or "U-law for North American Countries", depends on your country.
And select "Answer by Phone" if you act as the answer side.
At last, don't forget to click the "Enter" command
button.
4. In the "Mode" pop-pup menu, there is "port change"
item, you can change the COM port if you want.
The default COM port is COM5.
Now you have 2 options to use our ISDN phone. If you use other
AP or Hyperterminal, go to 5-9.
If you want to use our Configuration Ultility to dial or answer
a phone. Click the tab "Voice Dialer".
Original side, enter the phone number using the keypad then click
the "Dial" command button. For some phone systems, you need to
dial extension number, please enter the extension number using
keypad and click "Dial Ext" after the phone is connect.
Answer side, click the "Answer" command button when hearing the
RING.
Click the "Disc", the phone will disconnect.
5. Install the AP you want, for example, Hyperterminal, Procomm Plus,
BitCOMM and so on.
6. If you want to use the Hyperterminal.
And your desk top doesn't have Hyperterminal yet.
Please go to "Add/Remove program" in Control pannel
and add the "Communication" of the "Windows Setup"
tab. Note that you should restart again.
7. We now assume that you use the Hyperterminal.
8. Click the "Hypertrm.exe" icon, give a name (ex, IV128COM)
, give the telephone number you want to dial and
select the "Intelligent ISDN MODEM (modem)".
If the "dial" window appear, select "Cancel" first and
go to the Terminal Screen.
You can enter AT!V? to check your settings is correct or not.
9. If you are in the original side, enter ATDVxxxxxxx which xxxxxxx
is your telephone number. For some phone systems, you need to
dial extension number, please enter ATDEyyy which yyy is the
extension number after the phone is connect.
If you are in the answer side, just enter ATS0=1 and wait for call.

Q26: How to make a FAX transfer with IV128 through PSTN line in VCOMM
mode ?
A26:
1. Install IV128, see Q0&A0.
2. Insert our IV128 CARD in PCMCIA socket.
Plug the DAA dongle you purchased to the wall (RJ-11).
3. Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
In the "SWITCH TYPE" tab, you can ignore it.
In the "PTOTOCOL" tab, you can ignore it.
In the "CALL" tab, you can jgnore it.
In the "OTHER" tab, you can jgnore it.
In the "MODEM" tab, select the "Modem over Analog Telephone Line
(PSTN)".
In the "Voice Config" tab, you can ignore it.
At last, don't forget to click the "Enter" command
button.
4. In the "Mode" pop-pup menu, there is "port change"
item, you can change the COM port if you want.
The default COM port is COM5.
5. For the FAX AP, please select the COM5 or "Intelligent ISDN MODEM
(modem)". Now you can send/receive FAX correctly.

TOP
Q27: How to make a FAX transfer with IV128 through ISDN line in VCOMM mode ?
A27:
1. Install IV128, see Q0&A0.
2. Insert our IV128 CARD in PCMCIA socket.
Plug the U or S/T dongle you purchased to the wall (RJ-45).
3. Click the "Configuration Utility" icon of our
"ISDN TA configuration utility" program group on
desk top.
In the "SWITCH TYPE" tab, select the correct switch type.
In the "PTOTOCOL" tab, you can ignore it.
In the "CALL" tab, give the correct SPID and DN.
In the "OTHER" tab, you can jgnore it.
In the "MODEM" tab, select the "Modem over ISDN B-Channel".
In the "Voice Config" tab, select the "A-law for European countries"
or "U-law for North American Countries", depends on your country.
And select "Answer by Modem" if you act as the answer side.
At last, don't forget to click the "Enter" command
button.
4. In the "Mode" pop-pup menu, there is "port change"
item, you can change the COM port if you want.
The default COM port is COM5.
5. For the FAX AP, please select the COM5 or "Intelligent ISDN MODEM
(modem)".
With the original side, the "dial prefix" you should give "ATDM",
not "ATD" or "ATDT".
With the answer side, the "AT!V=1" should added after "AT&F" in the
initial string.
Now you can send/receive FAX correctly.

TOP
Q28: How do I install IV128 CAPI driver for Windows NT 4.0?
A28:
1. Enter Windows NT 4.0
2. Insert our card in the PCMICIA socket.
3. Click "Network" of the "Control Pannel". ( You have at least
already installed one kind of network card driver.)
4. Insert our "Windows NT driver disk (CAPI)" in A:
5. From the Network window, select the "Adapter" tab, click "Add".
6. Click "Have disks", give the path "A:", click "OK".
7 Now you will get the "56K MODEM + ISDN Adapter for CAPI" item in the
list box. Click "OK".
8. Now you get the "INTELLIGENT IV128 Setup" window.
Please make sure that the following settings are all correct:
(A) "I/O base" can not occupied by other device.
(B) "IRQ" is not confict.
(C) "Mem" setting is for PCMICA attritube memory use, you can
select one of the settings.
(D) For the "Pcmcia" setting, if you select the "CARDBUS", you can
work with the chip like "TI 113X" and "Cirrus Logic 6832" and
"O2 MICRO OZ6833T".
If you select the "365 COMP", you can work with Intel 82365
compatible chip.
(E) Last make sure "Line settings" are all correct.
After that, click "Continue".
9. At last, click "close".
10.Restart Windows NT again.
11.Now you can check our card is installed correctly or not.
Click the Program - Administrative Tools (Common) - Windows NT
Diagnostics. Click "Service" tab and "Device" command button and
check the "isdnta" status. If the status is running, it meas
good. If it's stop, try to change the value of I/O, IRQ, Mem and
Pcmcia setting.
Make sure the I/O, IRQ, Mem setting are not conflict with other
devices. You can click "Start" -- "Program" - "Administrative Tools
(Common)" - "Windows NT Diagnostics". Click "Resource" tab, now you
can check the "IRQ" and "I/O port".
Note: If you click "Start" -- "Programs" -- "Administrative Tools"
-- " Event Viewer", you will get the message "The IV128 System
IV128 Driver Service failed to start due to the following error:
The system can not find the file specified.". This should be
ignored. It is not an error.
12.Now you can install RVS-COM for Windows NT and run the CAPI
applications.
Run "c:\windows\system\status.exe" and try to connect you will
know the D-CH, B1-CH and B2-CH active or not and which protocol
currently run.
13.If you want to change the I/O, IRQ, Mem, Pcmcia, Switch Type,
PHONE0, PHONE1, SPID0 and SPID1, click "My Computer" -- "Control
Pannel" -- "Network" and then select the "Adapter", highlight
"INTELLIGENT IV128 Adapter", click the "Propertities" command
button. Now you can change the parameters you want.
Note: After changing some settings, you had better "power off"
and "power on". Do not let Windows NT do the "restart" for you.
It sometimes has no effect.

TOP
Q29: How do I uninstall IV128 CAPI driver for Windows NT 4.0?
A29: Click "Network" in "Control Pannel", select the "Adapter" tab,
highlight the "INTELLIGENT IV128 Adapter". Then click "remove".